Showing results: 2011 - 2025 of 3393 items found.
-
KMF 1 -
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR KMF 1. The KMF 1 search receiver is used according to the step voltage method. The cable line is scanned with two measurement probes that can be dismantled during transport. The battery-operated device is also suitable for locating multiple consecutive sheath faults.* Battery mode* Zero point compensation* accurate location of cable sheath faults* battery test
-
60-985-010 -
Pickering Interfaces Ltd.
The 60-985 series of LXI cables conform with the LXI WTB (Wired Trigger Bus) cable specification. They terminate in a 25 Pin Micro D connector at each end and use low loss silver plated cable incorporating 8 differential pairs each with separate shields. The cable to connector termination is designed to minimize inter-channel crosstalk and maintain excellent transmission line impedance.
-
AEMC Instruments
The AX500 Series is a comprehensive line of digital DC linear power supplies designed to meet the rigors of manufacturing, laboratory and education applications. Designed around highly efficient torodial transformers, they dissipate little heat, low electromagnetic emission and are designed for continuous duty cycle at full rated output. Two models are available offering single, dual and triple output capabilities.
-
AEMC Instruments
Comprehensive line of clamp-on current probes covers the entire spectrum of applications, from electrical panels to substations. AEMC Current Probes measure current without interrupting the circuit under test and extend the measuring capabilities of DMMs, recorders, power meters, and loggers. The numerous jaw sizes are designed to accommodate a wide variety of conductor diameters and ranges. Available for AC or DC measurements.
-
EverythingPCB
AkroMetrix provides a variety of products to help you identify and evaluate warpage: For warpage measurements along a production line or at room temperature, AkroMetrix has developed the LineMoiré Production Level Automated Flatness Inspection System. If you need to measure warpage and flatness during pre-defined temperature profiles, AkroMetrix's TherMoiré In-Process Warpage Measurement Systems may fit your requirements.
-
NX Pro+ -
Dynalab Test Systems, Inc.
The Dynalab NX Pro+ Wire HarnessTester is modular and is designed for applications requiring up to 32,768 test points. It has the same front end as the NX Pro Tester, but employs a series of Expansion Units to accommodate the test point cards. Testing for continuity, shorts, and a variety of components. Highly flexible and adaptable product line that meets the changing needs of wire harness manufacturers.
-
TD4000A -
Ponovo Power Co., Ltd.
TD series testing equipment is a HVDC Test Set consisting of control unit and DC high current output unit. And the TD series HVDC primary injection system includes 3 types, which could output 2000Adc/4000Adc/ 8000Adc and 0.1% high accuracy, suitable to be used for different HVDC testing requirements, such as in HVDC Converting station, or railway transportation line, etc.
-
Doble Engineering
Doble offers a comprehensive line of diagnostic equipment and software solutions for the verification of system protection. Our solutions allow you to challenge any protection and control circuit and simulate system condition. Our software is flexible and our equipment is modular allowing you to customize your testing program, adhere to your company's practices and procedures, while meeting regulatory requirements.
-
CX-LJ -
Shenzhen Chuangxin Instruments Co., Ltd.
*For measuring and testing the torque strain exerted by appliances with plug pins on socket-outlets, in accordance with IEC 60065 clause 15.4.1 and figure 11, IEC 60335-1 clause 22.3, IEC 60884-1 clause 14.23.2. *The balancing arm of the test apparatus pivots about a horizontal axis through the center lines of the contact tubes of the socket-outlet at a distance of 8 mm behind the engagement face of the socket-outlet.
-
2521 -
Shenzhen Chuangxin Instruments Co., Ltd.
*High measuring accuracy, high speed, easy to use, especially suitable for using in laboratory and automatic testing line *Test current AC / 5 ~ 30 (a), resistance Ω (0 ~ 600 m), time (1 ~ 99 s) shows at the same time;*Test time can be arbitrary setted;*Test alarm value can be arbitrary set up *Pass/fail sound and light alarm;
-
Duma Optronics LTD
For analyzing laser beam collimation its direction in space and its profile distribution proprietary instruments were developed. A collimated laser beam with a relatively large beam can be tested with the laser analyzing Autcollimator having an input apreture 100 mm, this device acompanied by AngleMeter U3 and the AngleMeter LA will provide a full product line for analyzing collimated or near collimation laser beams.
-
4013A(300V / 20A) -
PRODIGIT Electronics Co, Ltd.
4013A Digital Power Meter is designed to measure the power line parameters of AC / DC and DC / DC power supply. It is suitable for AC / DC Adapter, Charger, Quick Charger, LED Driver and DC / DC Converter. It is also suitable for uninterruptible power supply UPS, Regulators AVR, Inverter, batteries, AC / DC power supply / components ... and other applications.
-
4015A(500V / 20A) -
PRODIGIT Electronics Co, Ltd.
4015A Digital Power Meter is designed to measure the power line parameters of AC / DC and DC / DC power supply. It is suitable for AC / DC Adapter, Charger, Quick Charger, LED Driver and DC / DC Converter. It is also suitable for uninterruptible power supply UPS, Regulators AVR, Inverter, batteries, AC / DC power supply / components ... and other applications.
-
Pinpoint Laser Systems
The Microgage PRO is the next generation in laser measuring and alignment tools. This extremely versatile measuring and alignment tool combines key features and capabilities into one portable, compact, easy to use, product for multiple industries. A precise laser beam forms a straight reference line for a machine or assembly and each receiver measures in two axial directions, horizontal and vertical (X & Y).
-
Duma Optronics LTD
The alignment product line provides full solutions for applications such as: alignment of laser cavities, straightness measurement, machine alignment, wide-bed printers alignment and others. The AlignMeter system simultaneously measures incoming laser beam position (in µm) and angle (in µRad).It is a powerful compact device perfect for alignment monitoring, for testing the drift, centration and beam alignment relative to the outer housing or tube.